Whirlpool HAR 643 T F Instrucciones de uso descargar pdf (Pagina 5)

- Install a separator panel under the hob.

- The lower part of the product must not be accessible after installation.

- Do not t the separator panel if an undertop oven is installed.

IMPORTANT:

- The distance between the underside of the appliance and the separator panel

must respect the dimensions given in the gure;

- If an oven is installed under the hob, make sure the oven is equipped with a

cooling system;

- Do not install the hob above a dishwasher or washing-machine, so that the

electronic circuits do not come into contact with steam or moisture which could

damage them.

PLACING THE HOB

After the electrical connection (see the chapter “Electrical connection”) position each xing clips on the dedicated slots on the lateral sides of the hob as shown

in the picture. Then push the hob inside the cut out and check that the glass is at and parallel to the worktop. The xing clips are designed for every type of

worktop material (wood, marble, etc).

IMPORTANT:

- Use protective gloves during hob installation

PREPARING THE CABINET FOR FITTING.

- To remove the hob, use a screwdriver (not provided) to prise off the xing clips on the underside of the appliance.

WARNING

6-7 cm

Min. 20 mm

Min. 5 mm

X 4

SAFEGUARDING THE ENVIRONMENT

Disposal of packing

The packing material is 100% recyclable and marked with the recycling symbol ( ).The various parts of the packing must not be dispersed in the environment,

but disposed of in compliance with local regulations.

Disposal

This appliance is marked in conformity with European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is correctly disposed of, the user can help prevent potentially negative consequences for the environment and the health of people.

The symbol on the appliance or the accompanying documentation indicates that this product should not be treated as domestic waste but must be taken

to an appropriate collection point for recycling WEEE.

DECLARATION OF CONFORMITY

- This appliance has been designed, manufactured and marketed in conformity with the safety requirements of “Low Voltage” Directive 2006/95/EC (replacing

73/23/EEC as amended) and protection requirements of “EMC” Directive 2004/108/EC.

- This appliance meets the eco design requirements of European Regulation N. 66/2014, in conformity to the European standard EN 60350-2.

INSTALLATION

After unpacking the product, check for

any damage during transport. In case

of problems, contact the dealer or the

After-Sales Service.

For buit-in dimensions and installation

instruction see the pictures in this

paragraph.

A minimum distance must be

maintained between the hob and

the hood above it. Please refer to the

user manual of the hood for more

informations.

Min. 40 cm

Min. 10 cm

R = Min. 6,5 mm

Max. 8 mm

490 mm

560 mm

Min. 70 mm

6 mm

min 20 mm

513 mm

583 mm

560 mm

490 mm

R = 11,5 mm

R = Min. 6,5 mm

FLUSH INSTALLATION

482 mm

552 mm

42/46 mm

510 mm

580 mm

Min. 70 mm

STANDARD INSTALLATION

580 X 510 mm

R = Min. 6,5 mm

Max. 8 mm

490 mm

750 mm

Min. 70 mm

513 mm

Min. 70 mm

773 mm

750 mm

490 mm

482 mm

742 mm

510 mm

42/46 mm

R = 11,5 mm

R = Min. 6,5 mm

6 mm

min 20 mm

FLUSH INSTALLATION

770 mm

STANDARD INSTALLATION

770 X 510 mm

1 2 3 4 5 6 7 8 9 10

Comentarios a estos manuales

Sin comentarios

Whirlpool HAR 643 T F Instrucciones de uso Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Whirlpool HAR 643 T F