Whirlpool PI 940 AT (IX) NG Instrucciones de uso descargar pdf (Pagina 2)

Installation

a) If the cabinet(s) located next to the cooktop are

higher than the cooktop itself, the cabinet(s) must be

installed at least 100 mm from the edge cooktop;

b) Hoods must be installed in accordance with the

instructions contained in the installation manual for

the hoods themselves, and no less than 650 mm

from the cooktop;

c) In the case of the 900 mm cooker hoods, besides

following the recommendations in point b), the

cabinets should be positioned next to the hood at a

height of at least 540 mm from the top . The cabinet

should always be installed at a height from the top

which allows easy use of pots and pans on the

cooker.

d) Should the cooktop be installed directly under a

cupboard, the latter should be at least 700 mm

(millimetres) from the top, as shown in Figure.

e) The dimensions of the cutout for the appliance must

be those indicated in the figure. Clamps are provided

to fasten the cooktop to counters measuring from 20

to 40 mm in thickness. To fasten the cooktop

securely, it is recommended that all the clamps be

used.

Fixing to the housing unit

Proceed with fixing to the housing unit as follows (fig.1):

· mount the hooks “B”, partly tightening the provided

screws “A” into the relative holes;

· position the provided sealing gasket “X” 5÷6 mm from

the edge of the installation hole, matching up the two

ends of the seal without overlapping;

· insert the hob into the hole, making sure it is

positioned centrally and that the edge adheres to the

sealant;

· position the hooks “B” correctly, as shown in figure

and then tighten the screws “A” to hold them in place;

Gas connection

Gas supply connection

• Check that the appliance is set for the type of gas

available and then connect it to the mains gas piping

or the gas cylinder in compliance with current

regulations and standards.

• This appliance is designed and set to work with the

gas indicated on the label situated on the actual hob.

If the gas supply is other than the type for which the

appliance has been set, proceed with replacing the

corresponding nozzles (provided), following

instructions given in the paragraph “Adaptation to

different types of gas”.

• For trouble-free operation, suitable use of energy and

longer life of the appliance, make sure that the supply

pressure complies with the values indicated in the

table 1 "burners and nozzles specifications, otherwise

install a special pressure regulator on the supply pipe

in compliance with current standards and regulations.

• Connect in such a way that the appliance is

subjected to no strain whatsoever.

Either a rigid metal pipe with fittings in compliance with

the standards in force must be used for connecting to

the nipple union (threaded ½"G male fitting) situated at

the rear of the appliance to the right (Fig.2), or flexible

steel pipe in compliance with the standards in force,

which must not exceed 2000 mm in length.

Should it be necessary to turn the fitting, the gasket

(supplied with the appliance) must be replaced.

Upon completion of installation, check the gas circuit,

the internal connections and the taps for leaks using a

soapy solution (never a flame).

Also check that the connecting pipe cannot come into

contact with moving parts which could damage or

crush it. Make sure that the natural gas pipe is

adequate for a sufficient supply to the appliance when

all the burners are lit.

Important: A pressure regulator, in compliance with the

Fig.2

Min.

700mm

50 m

840 mm

55 mm

480 mm

Fig.1

1 2 3 4 5 6 7 ... 11 12

Comentarios a estos manuales

Sin comentarios

Whirlpool PI 940 AT (IX) NG Instrucciones de uso Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Whirlpool PI 940 AT (IX) NG