Whirlpool AKR 362/IX Instrucciones de uso descargar pdf (Pagina 2)

ELECTRICAL CONNECTION

This operation must be performed by a qualied technician.

The electrical connections must comply

with local regulations.

• The earthing of this appliance is com-

pulsory by law.

• Do not use an extension cord.

Earth

(yellow/green)

IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.

ASSEMBLY

After having cleaned the perimeter surface,

apply the supplied gasket to the hob as shown in

the gure.

Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.

NOTE: the power supply cable must be long enough to permit its upward extraction.

To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and

fasten them by means of their screws in accordance with the thickness of the worktop (see the following gures).

Top 20 mm

Top 30-50 mm

ADJUSTMENT TO DIFFERENT TYPES OF GAS

This operation must be performed by a qualied technician.

If the appliance is intended to operate with a dierent gas from the gas type stated on the rating plate and information

label on the top of the hob, change the injectors.

Remove the information label and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Instruction.

• The gas nozzles must be changed by After Sales Service or a qualied technician.

• Nozzles not supplied with the appliance must be ordered from After Sales Service.

• Adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.

IMPORTANT: should you experience diculty in turning the burners knobs, please contact the After Sales Service

for the replacement of the burner tap if found to be faulty.

REPLACING THE INJECTORS see the injector table in the Instruction

• Remove grids (A).

• Extract burners (B).

• Using a socket spanner of the appropriate size unscrew the injector (C),

unscrew the injector to be replaced.

• Replace it with the injector suitable for the new type of gas.

• Re-assemble the injector in (D).

• If you have a multiple crown burner use side spanner to replace the

injector (E).

Before installing the hob, remember to ax the gas calibration plate sup-

plied with the injectors in such a way that it covers the existing informa-

tion relating to gas calibration.

ADJUSTING MINIMUM GAS SETTING OF TAPS

To ensure that the minimum setting is correctly adjusted, remove the knob

and proceed as follows:

• tighten screw to reduce the ame height (-);

• loosen screw to increase the ame height (+).

The adjustment must be performed with the tap in minimum gas setting

position (small ame)

• The primary air of the burners does not need to be adjusted.

• At this stage, light up the burners and turn the knobs from max posi-

tion

to minimum position to check ame stability.

Upon completion of adjustment, reseal using sealing wax or an equivalent

material.

REFERENCE TO LOCAL REGULATIONS

Ensure that the installation and gas connections are performed by a qualied technician, following the manufactu-

rer’s instructions and in compliance with current local safety regulations..

AFTERSALES SERVICE

Before calling the After-Sales Service, make sure you can give the following

information:

- type of fault or problem;

- exact model (written on the label axed to the instruction/warranty);

- service number that follows the word SERVICE on the rating plate

under the hob and on the label axed to instruction/warranty;

- your complete address and phone number.

If any repairs are required, please contact an authorised After-Sales Service,

as indicated in the warranty.

WARNING

1 2 3 4

DANGER 1
WARNING 1

Comentarios a estos manuales

Sin comentarios

Whirlpool AKR 362/IX Instrucciones de uso Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Whirlpool AKR 362/IX