Whirlpool AWM 6100 Instrucciones de uso descargar pdf (Pagina 12)

The appliance vibrates during the spin cycle.

Check whether:



the appliance is levelled and solidly installed on

all four feet (see Installation Instructions);



the transit bolts have been removed. The transit

bolts must be removed before the appliance can

be used (see Installation Instructions).

Final spin results are poor:

The appliance has an imbalance detection and

correction system. If individual heavy articles are

loaded (bathmat, bathrobe, etc.) this system may

reduce the spin speed automatically to protect the

appliance or even interrupt the spin cycle

altogether, if the imbalance is too great even after

several spin starts.



If the laundry is still too wet at the end of the

cycle, add smaller articles of laundry to balance

the load and repeat the spin cycle.



Excessive foam formation may prevent spinning.

Ensure correct amount of detergent is used

No water or insufficient water supply:



the appliance has a safety hose and the safety

valve has opened (red indicator in the safety

valve inspector window).

In this case replace it with a new safety hose.

What should I do when the automatic safety system detects a malfunction?

The programme is interrupted and various indicators (if available) point to the source of the fault.

Fault description table

a. Water inlet fault (no or insufficient water supply)

The Water tap indicator is on or the display

alternately shows FH. Switch off the appliance

by turning the programme selector to the  

position and unplug it.

Check whether:



the water tap is completely open, and the water

supply pressure is sufficient;



the water inlet hose is kinked;



the mesh filters are blocked (see Care and

Maintenance / Water Hose Mesh Filters);



the water inlet hose is frozen.

Connect the appliance to the electrical supply.

Reselect the desired programme and press the

Start/

Pause

button again to continue with the programme

(do not add detergent for this programme)

b.Draining out fault

The display alternately shows FP. Switch off the

appliance by turning the programme selector to

the   position and unplug it.

Check whether:



the drain hose is kinked (see Installation

Instructions);



the pump / filter are blocked (see Removing the

Filter / Draining Residual Water).

IMPORTANT

: before draining, allow the wash

water to cool down.



the drain hose is frozen.

Connect the appliance to the electrical supply.

Reselect the desired programme and press the

Start/

Pause

button again to continue with the programme

(do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see After-Sales Service).

c. Electrical module fault

The display shows F4 to F15.



Switch off the appliance. Select a programme

and press the

Start/Pause

button once again.

The programme will continue.



If the fault re-occurs, contact After Sales Service

(See After-Sales Service).

d. Water Stop fault

(if available)

An audible tone sounds. The light of the Water

Stop indication is on.

The display shows FA and the pump is running.

Switch off the appliance by turning the programme

selector to the   position, unplug the appliance

and make sure that the water tap is closed.

The Water Stop may have been triggered by:

too much foam.

a leak in the inlet hose or in the appliance.

Tilt the appliance forwards carefully to allow the

collected water to flow out from the bottom of the

appliance.

Clean up the water and make the area safe.

Then:

connect the appliance to the electrical supply,

open water supply to machine (if

Start/Pause

button is not pr essed, but machine begins to fill,

close water supply and call After-Sales Service),

reselect the desired programme and press the

Start/Pause

button (there is no need to add

additional detergent). The programme will continue.

If the faults occurs again, call After-Sales Service with

details about the fault (see After-Sales Service).

Small lamp lights up Digital display Fault description

Water tap FH Water inlet fault

- FP Draining fault

- from F4 to F15 Electrical components fault

Water Stop FA Water Stop fault

3gb05149.fm5 Page 12 Wednesday, February 14, 2001 9:18 AM

Black Process Plate

1 2 ... 7 8 9 10 11 12 13 14 15 16

Comentarios a estos manuales

Sin comentarios

Whirlpool AWM 6100 Instrucciones de uso Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Lavadoras Whirlpool AWM 6100