Whirlpool TI 6401 (NR) IT Instrucciones de uso descargar pdf (Pagina 12)

The thickness of the supporting surface should be taken

into account when choosing screws for the fixing hooks:

 30 mm thick: 17.55 mm screws

 40 mm thick: 7.55 mm screws

Fix the hob as follows:

1. Use short flat-bottomed screws to fix the 4 alignment

springs in the holes provided at the central point of each

side of the hob.

2. Place the hob in the cavity, make sure it is in a central

position and push down on the whole perimeter until the

hob is stuck to the supporting surface.

3. For hobs with raised sides: After inserting the hob into

its cavity, insert the 4 fixing hooks (each has its own pin)

into the lower edges of the hob, using the long pointed

screws to fix it in place, until the glass is stuck to the

supporting surface.

! The screws for the alignment springs must remain

accessible.

! In order to adhere to safety standards, the appliance

must not come into contact with electrical parts once it

has been installed.

! All parts that ensure the safe operation of the appliance

must not be removable without the aid of a tool.

Electrical connection

! The electrical connection of the hob and any built-in

oven must be carried out separately, both for safety

purposes and to make extracting the oven easier.

Single-phase connection

The hob is equipped with a pre-connected electricity

supply cable, which is designed for single-phase

connection. Connect the wires in accordance with the

instructions given in the following table and diagrams:

Separate the wires and connect them in accordance with

the instructions given in the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

230V 1+N ~

50 Hz

: yellow/green;

N: the two blue wires

together

L: brown and black

together

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

 400V - 2+N ~ 50 Hz

 230V 3 ~ 50 Hz

 400V - 2+2N ~ 50 Hz

Voltage and

mains frequency

Electrical cable Wire connection

400V - 2+N ~

50 Hz

230V 3 ~

50Hz

: yellow/green;

N: the two blue wires together

L1: black

L2: brown

400V - 2+2N ~

50 Hz

: yellow/green;

N1: blue

N2: blue

L1: black

L2: brown

Connecting the electricity supply cable to the mains

The appliance must be directly connected to the mains

using an omnipolar circuit-breaker with a minimum

contact opening of 3 mm installed between the appliance

and the mains. The circuit-breaker must be suitable for

the charge indicated and must comply with current

electrical regulations (the earthing wire must not be

interrupted by the circuit-breaker). The supply cable must

not come into contact with surfaces with temperatures

higher than 50°C.

! The installer must ensure that the correct electrical

connection has been made and that it is fully compliant

with safety regulations.

Before connecting the appliance to the power supply,

make sure that:

 The appliance is earthed and the plug is

compliant with the law.

 The socket can withstand the maximum power of

the appliance, which is indicated on the data

plate located on the appliance itself.

 The voltage is in the range between the values

indicated on the data plate.

 The socket is compatible with the plug of the

appliance. If the socket is incompatible with the

plug, ask an authorised technician to replace it.

Do not use extension cords or multiple sockets.

! Once the appliance has been installed, the power

supply cable and the electrical socket must be easily

accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only.

! The manufacturer declines any liability should these

safety measures not be observed.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 47 48

Comentarios a estos manuales

Sin comentarios

Whirlpool TI 6401 (NR) IT Instrucciones de uso Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Whirlpool TI 6401 (NR) IT